DirectLink remote control for Supla Thermostat

piomar2
Posts: 369
Joined: Fri Apr 26, 2019 5:32 pm
Location: Bukowice

Now after 1min12sec changed to 20.0
piomar2
Posts: 369
Joined: Fri Apr 26, 2019 5:32 pm
Location: Bukowice

Everything indicates that I made the mistake and uploaded the wrong sketch (thermostat) and it caused errors. Now, I think everything will be ok. Once again, I'm sorry but this is my inattention. Now it updates nicely. Elmaya is a champion over a champion !!!
elmaya
Posts: 1482
Joined: Wed Jun 27, 2018 5:48 pm
Location: El Saucejo - Sevilla

piomar2 wrote: Thu Nov 07, 2019 6:58 pm Everything indicates that I made the mistake and uploaded the wrong sketch (thermostat) and it caused errors. Now, I think everything will be ok. Once again, I'm sorry but this is my inattention. Now it updates nicely. Elmaya is a champion over a champion !!!
I'm glad it's finally fine.
It should work with all my software for Supla thermostats.
I welcome any suggestions for possible improvements.
piomar2
Posts: 369
Joined: Fri Apr 26, 2019 5:32 pm
Location: Bukowice

Sorry again. I have a request. Can you send me the * .ino version "D_Link_Termostat_Remote_test_DOUT_16Mbit.bin" yet? It will be easier for me. I got used to compiling in arduino and not uploading * .bin. Thanks
kotogi
Posts: 78
Joined: Thu Sep 24, 2020 11:02 pm

I cannot configure the device to get the temperature values on the display.
"Link Temp - paste the DirectLink corresponding to the temperature channel." What should I enter from the obtained direct link from SUPLA website
https://svr41.supla.org/direct/837/W6SgrRUXgbxk89?
Pytam tylko jak muszę.
elmaya
Posts: 1482
Joined: Wed Jun 27, 2018 5:48 pm
Location: El Saucejo - Sevilla

kotogi wrote: Wed Sep 22, 2021 12:57 pm I cannot configure the device to get the temperature values on the display.
"Link Temp - paste the DirectLink corresponding to the temperature channel." What should I enter from the obtained direct link from SUPLA website
https://svr41.supla.org/direct/837/W6SgrRUXgbxk89?
Attachments
wifimanager.jpg
wifimanager.jpg (21.71 KiB) Viewed 2204 times
kotogi
Posts: 78
Joined: Thu Sep 24, 2020 11:02 pm

Problem tkwił w połączeniu internetowym .
Pytam tylko jak muszę.
kotogi
Posts: 78
Joined: Thu Sep 24, 2020 11:02 pm

I have a problem that the remote control does not display the set temperature (in its place is displayed -127) the direct link is certainly good because after switching the links to the temperature and the set temperature, the remote control correctly shows the set temperature (in place of the temperature).
When I put the link to the set temperature in both places, the remote control displays correctly both in the place of the temperature and the set temperature.
It seems to me that the reason for this behavior is too slow internet connection.
The question is whether it is not possible to change the server response timeouts to eliminate this.
Pytam tylko jak muszę.
elmaya
Posts: 1482
Joined: Wed Jun 27, 2018 5:48 pm
Location: El Saucejo - Sevilla

connect serial monitor to the module to see exactly what is happening.
kotogi
Posts: 78
Joined: Thu Sep 24, 2020 11:02 pm

mounted file system
reading config file
opened config file
104
{"Supla_server":"svr41.supla.org","D_Link_1":"/direct/846/Qa3EGQzS9HHiX","D_Link _2":"/direct/847/5bPrcodFAD","D_Link_3":"/direct/848/GAhQ7rxvbsp_XPN","Link_T":" /direct/849/BJzF__9WDhnXN","Link_T2":"/direct/852/9oPCZbbDjUFeTs"}
parsed json
...
Connected
Adres IP:
192.168.0.153 / 255.255.255.0 / 192.168.0.1
(RSSI): -68 dBm
failed
failed
failed
failed
failed
failed
failed
failed
failed
failed
failed
failed
failed
failed
failed
failed
connection failed
connection failed
connection failed
connection failed
connection failed
connection failed
connection failed
connection failed
connection failed
connection failed
connection failed
connection failed
Pytam tylko jak muszę.
Post Reply

Return to “Ideas and concepts”