Supla Button 4 direct links

wsosniak
Posts: 718
Joined: Sat Jun 02, 2018 8:02 am

i can confirm the same like PuteR -> the newest ver for 6 links works without self executing.
i did :
- i loaded your newest bin (6 links 60 chars) into my ESP12
- i moved ESP12 in the place where i had problem with self execution of links
- i cant see any problem now

thx a lot !!
elmaya
Posts: 1482
Joined: Wed Jun 27, 2018 5:48 pm
Location: El Saucejo - Sevilla

Thanks for the help.
updated on page 1.
User avatar
PuteR
Posts: 1421
Joined: Wed Dec 06, 2017 10:07 am

We thank you :D
User avatar
PuteR
Posts: 1421
Joined: Wed Dec 06, 2017 10:07 am

elamya What is the mistake from

Code: Select all

<html>
<head><title>400 Bad Request</title></head>
<body>
<center><h1>400 Bad Request</h1></center>
<hr><center>nginx/1.15.8</center>
</body>
</html>
in D_Link_Config_5_s_x6, everything worked fine, and there was a problem yesterday. Link does not perform when the module I have on the wall, unless I hold the button longer it will be done.

After connecting to a computer, a serial monitor throws out the above error. After re-uploading the software on the computer, it works ok, as I will give the wall the same again.

I would add that I did not have any pull ups made, but until now everything worked correctly, but is pull up required ??
elmaya
Posts: 1482
Joined: Wed Jun 27, 2018 5:48 pm
Location: El Saucejo - Sevilla

PuteR wrote: Tue Apr 02, 2019 6:43 am elamya What is the mistake from

Code: Select all

<html>
<head><title>400 Bad Request</title></head>
<body>
<center><h1>400 Bad Request</h1></center>
<hr><center>nginx/1.15.8</center>
</body>
</html>
in D_Link_Config_5_s_x6, everything worked fine, and there was a problem yesterday. Link does not perform when the module I have on the wall, unless I hold the button longer it will be done.

After connecting to a computer, a serial monitor throws out the above error. After re-uploading the software on the computer, it works ok, as I will give the wall the same again.

I would add that I did not have any pull ups made, but until now everything worked correctly, but is pull up required ??
Check power supply
User avatar
PuteR
Posts: 1421
Joined: Wed Dec 06, 2017 10:07 am

I actually changed the power source and the problem stopped 😀. Thanks a lot
Jeki87
Posts: 91
Joined: Wed Jun 21, 2017 10:29 am

I have a problem with direct links! I Generated the link
roller blinds open
the entrance gate open
the garage door open
wicket open
the light switch
only operate blinds open close gateway the rest links does not work does not send the address the diode does not blink twice wemos hangs for 5 seconds tries on all pins d1-d7 only blinds work and the entrance gate on every gpio in what problem ??
Software D_Link_Config_5_s_x6.bin
Wemos D1 mini
elmaya
Posts: 1482
Joined: Wed Jun 27, 2018 5:48 pm
Location: El Saucejo - Sevilla

check the direct links in the browser,
possibly have some typographical error or some space added
szym3k
Posts: 268
Joined: Mon May 15, 2017 10:32 am

hello,
when I click the button in the terminal I have:
connecting to x.x.com
connection failed


while when I connect to public server everything is ok.

i tried after ip, hostname...
elmaya
Posts: 1482
Joined: Wed Jun 27, 2018 5:48 pm
Location: El Saucejo - Sevilla

szym3k wrote: Mon Dec 16, 2019 12:44 am hello,
when I click the button in the terminal I have:
connecting to x.x.com
connection failed


while when I connect to public server everything is ok.

i tried after ip, hostname...
I guess you tried with the local IP?
Do you have port 443 enabled on your server?
Post Reply

Return to “Ideas and concepts”